MG20 Ear Pads: Comfort, Fit, and When to Replace

Quick answer

MG20 Ear Pads are lambskin-wrapped memory foam pads that attach magnetically, so you can pull them off for cleaning or replacement without tools. Replace them when the foam flattens, the lambskin cracks or peels, or the seal around your ear loosens. Genuine MG20 replacement ear pads keep the fit, breathability, and comfort the headphones were designed around.

If your MG20 headphones feel less cushioned than they used to, the ear pads are usually the first part to show wear. They take the pressure of every listening session, absorb sweat and oils, and slowly compress over time. Knowing how they fit and when to swap them keeps the headphones comfortable and the sound consistent.

These answers cover the questions MG20 owners ask most: how the pads attach, how they should feel, how to clean them safely, and how to tell the difference between normal softening and a pad that actually needs replacing.

How do MG20 Ear Pads attach?

They attach with magnets. To remove a pad for cleaning or replacement, gently pull it off the headphones and the magnets release. There are no screws, clips, or adhesive to work around, so you can take both pads off in seconds.

When you put a pad back on, line it up with the housing and let the magnets pull it into place. You should feel it seat evenly rather than sit at an angle. If a pad feels loose or shifts when you press it, lift it off and reseat it before you start listening.

• Pull straight away from the housing rather than twisting, which keeps the pad shape intact.
• Reseat by aligning the pad first, then letting the magnets do the work.

What makes MG20 Ear Pads comfortable?

The pads are made of lambskin-wrapped memory foam, a combination chosen for comfort and breathability. The memory foam cushions and distributes pressure around the ear, while the lambskin surface feels soft against skin and lets the area breathe better than a fully sealed synthetic surface.

That breathability matters most during long sessions. If you wear the headphones for hours at a time, a pad that traps heat gets uncomfortable fast, no matter how plush the foam is. The lambskin wrap is the main reason MG20 Ear Pads stay wearable through a full workday or a long flight.

• Lambskin-wrapped memory foam is designed for comfort and breathability.
• Take short breaks during very long sessions to let the pads and your ears air out.

How should MG20 Ear Pads fit?

They should sit fully around your ear with light, even pressure and no gaps at the edges. The pad should rest against your head without clamping hard. If you feel pressure points at the top of your jaw or behind your ear, the pad may be seated unevenly or the foam may have started to compress.

A good fit also helps the sound. When the pad seals properly around the ear, you hear more of the low end and less outside noise. When the seal breaks, bass tends to thin out and you find yourself turning the volume up, which is a sign the pad is no longer doing its job.

• Check the seal by pressing gently around the rim; the pad should stay flush against your head.
• If one side feels different from the other, compare both pads for flattening or deformation.

How do I clean MG20 Ear Pads?

Pull the pads off first, then wipe the lambskin surface with a soft, dry or very slightly damp cloth. Avoid soaking them, machine washing, or using harsh solvents, since the lambskin wrap and the foam underneath can both be damaged by excess moisture and aggressive cleaners.

Let the pads air dry completely before putting them back on the headphones, and keep them away from direct heat. For routine care, a quick wipe after sweaty sessions is enough to keep the surface from building up oils and residue.

• Wipe, don't soak; lambskin and memory foam both dislike standing water.
• Air dry fully before reattaching so moisture doesn't sit against the driver housing.

When should I replace MG20 Ear Pads?

Replace them when the foam no longer springs back, when the lambskin surface cracks, flakes, or peels, or when the pad stops sealing around your ear. Flattening is gradual, so the change is easy to miss until you compare a worn pad with a fresh one.

A practical test: press the pad with your thumb and watch how quickly it recovers. A healthy pad bounces back; a worn one stays compressed. If you have to press the headphones against your head to get the bass back, the pads are past their useful life.

• Foam that stays dented after pressing is a clear replacement signal.
• Cracked or peeling lambskin can't be repaired and should be replaced.

Do I need to replace both pads at once?

Yes, in most cases. Both pads wear at roughly the same rate, and replacing only one leaves you with mismatched cushioning and an uneven seal, which can make the headphones feel lopsided and shift the stereo balance.

Since MG20 Ear Pads are sold as a pair-ready replacement part, swapping both at the same time keeps the fit and comfort consistent. Keep the older set only if it's still in good shape and you want a spare.

• Replace in pairs to keep pressure and seal symmetrical.
• If only one pad looks worn, check the other before ordering just one.

Are MG20 Ear Pads easy to replace yourself?

Yes. Because the pads attach magnetically, replacement is a pull-and-press job with no tools. Pull the old pad off, align the new one, and let the magnets seat it. The whole swap takes a minute or two.

The main thing to avoid is forcing or twisting a pad into place. If a new pad doesn't sit flush, lift it and try again rather than pressing harder.

• No tools required: the magnets release when you pull gently.
• If a pad won't seat, realign instead of forcing it.

MG20 Ear Pad Checkpoints

Attachment check

Pull a pad gently; it should release from the magnets without resistance or tools. If it releases cleanly and reseats flush, the attachment is working as designed.

Foam recovery test

Press the pad with your thumb and watch how quickly it springs back. Foam that stays dented means it's time to order replacements.

Surface inspection

Look for cracks, flaking, or peeling on the lambskin wrap. Any of these means the pad can't be cleaned back to health; replace it.

Seal and sound check

Listen for thinning bass or a looser fit around your ear. A broken seal is a fit problem and a sound problem at the same time.

Cleaning routine

Wipe the lambskin with a soft, barely damp cloth and air dry fully before reattaching. Consistent light cleaning is what delays the next replacement.

Product facts

• MG20 Ear Pads: Made of lambskin-wrapped memory foam and designed to provide superior comfort and breathability; to remove for cleaning or replacement, gently pull the ear pads off the headphones and the magnets will release. This is the material and attachment system behind the comfort, fit, and cleaning advice above, and it explains why replacement is a tool-free job.
• MG20 Mercedes-AMG: The Mercedes-AMG lineup of headphones and earphones features high-performance materials including magnesium and carbon fiber and delivers bold, exhilarating sound. If you own this MG20 variant, the same magnetic ear pad system and care routine apply, so replacement pads and cleaning steps carry over.

MG20 Ear Pads are simple to live with: lambskin-wrapped memory foam for comfort and breathability, magnetic attachment for easy cleaning and replacement. Wipe them regularly, replace them in pairs when the foam stops recovering or the surface breaks down, and your MG20 headphones will keep feeling the way they did on day one.